Spring Rate Calculator & Converter (kg/mm, lb/in, N/mm)

Convert coilover spring rates between kg/mm, lb/in and N/mm, work out your actual wheel rate from the motion ratio, and see what ride frequency a given spring puts your car at. Everything runs on this page; nothing is sent anywhere.

8 kg/mm = 448 lb/in

= 78.5 N/mm · 1 kg/mm = 55.997 lb/in

“8k” on a Japanese or European spring means 8 kg/mm. Most US catalogs quote lb/in. Multiply kg/mm by 56 to get lb/in, or divide lb/in by 56 to get kg/mm.

Spring rate conversion chart

Quick reference for the rates most coilover kits are sold in. 1 kg/mm = 55.997 lb/in = 9.807 N/mm.

kg/mm lb/in N/mm
kg/mm lb/in N/mm

What a spring rate actually tells you

A spring rate is the force needed to compress the spring one unit of distance: an 8 kg/mm spring takes 8 kilograms to compress one millimetre, a 448 lb/in spring takes 448 pounds to compress one inch, and those are the same spring. On a linear spring the rate is constant through its travel; a progressive spring gets stiffer as it compresses. Nearly all coilover kits built for track use run linear springs, because a constant rate is what makes damping predictable and what a shock dyno can be matched to.

Two things that get confused with spring rate: preload and ride height. Winding the spring perch up against a linear spring does not make it stiffer; it changes how much load the spring carries at full droop, and on a true coilover with independent height adjustment it should not be used to set ride height at all. Ride height is set with the lower bracket or body length, which is why kits with independent ride height and travel adjustment matter: you can put the car at the height you want without eating into bump travel or cranking preload into the spring.

Spring rate vs wheel rate

The tire never feels the spring rate directly. It feels the wheel rate, which is the spring rate multiplied by the square of the motion ratio (how far the spring moves for every unit the wheel moves). A MacPherson strut sits almost in line with the wheel, so spring rate and wheel rate are close. A spring mounted partway along a control arm, or in a separate spring bucket on a toe arm, moves a fraction of the wheel travel, and because the ratio is squared, a small change in leverage makes a big change in rate. That is why the same chassis can carry wildly different spring numbers depending on where the spring is mounted, and why comparing rates between two different cars, or between a divorced and a true-rear setup on the same car, tells you very little until you convert both to wheel rate or ride frequency.

Why we don't publish a spring rate for each kit

Every Thunder Lane kit ships with spring rates chosen for the car it is going on, and we confirm them with you before the dampers are valved, because the right rate depends on things a product page cannot know: the tire you run, how low the car sits and how much bump travel is left there, whether it has aero, whether it drifts, grips or dailies, and what sway bars are on it. The calculator above will get you to a sensible starting frequency for your corner weights. What it cannot do is tell you whether that spring will bottom the damper at your ride height, or how the valving has to change to control it. That is the conversation we have in the build consultation, and it is why the dyno sheets that ship with every kit match the spring that is actually on the car.

Changing spring rates on an existing kit

Swapping to a stiffer or softer spring without re-valving the damper is the most common way a good coilover ends up feeling wrong. A damper is valved for a range of spring rates; move far outside it and the car is either under-damped (floaty, slow to settle, wallows in transitions) or over-damped (harsh, skips over bumps, tire loses contact). If your build has changed enough to need a different rate, the damper usually needs to see the dyno again. Every Thunder Lane damper is rebuildable and re-valvable, so a rate change is a service job, not a new kit.

FAQ

How do I convert kg/mm to lb/in?

Multiply by 55.997, or by 56 for a close enough answer. An 8 kg/mm spring is 448 lb/in; a 10 kg/mm spring is 560 lb/in. To go the other way, divide lb/in by 56.

What does “8k” or “10k” mean on a coilover spring?

Kilograms per millimetre. An 8k spring is 8 kg/mm, which is 448 lb/in. The “k” is shorthand used by Japanese and European spring makers and has nothing to do with thousands.

Is a higher spring rate always stiffer?

At the spring, yes. At the wheel, only if the motion ratio is the same. A 12 kg/mm spring in a divorced rear spring bucket can produce a lower wheel rate than a 7 kg/mm spring on a true-rear coilover on the same car, because the bucket spring moves less than the wheel. Compare wheel rates or ride frequencies, not spring numbers.

Does preload change the spring rate?

No. On a linear spring, preload changes how much force the spring carries at full droop, not how much force it takes to compress it a further inch. Preload affects ride height on kits without independent height adjustment and affects how the car behaves at full droop; it does not make the spring stiffer.

What spring rate should I run for daily driving?

Whatever puts your car in roughly the 1.0–1.5 Hz ride-frequency range for its corner weights and motion ratio, assuming the damper is valved for it. Use the ride frequency tab above with your car's weights. A “comfort” coilover setup is as much about valving as about the spring, which is why we build street kits differently rather than just fitting softer springs.

Do I need new damping if I change spring rates?

Usually, if the change is more than a step or two. Dampers are valved for a range of spring rates; outside that range the car is either under- or over-damped. Thunder Lane dampers are rebuildable and re-valvable, so a spring change is a service, not a replacement.

What are Swift springs, and do they change the rate?

Swift springs are a lighter, more consistent linear spring offered as an optional upgrade on our kits. The rate you choose stays the same; what changes is the spring's weight, its resistance to sag over time and how linear it stays near the end of its travel.

Why does the calculator need unsprung weight?

Ride frequency is calculated on the mass the spring actually carries, which is the corner weight minus the wheel, tire, brake and roughly half the suspension links at that corner. A typical street car runs 80–110 lb of unsprung weight per corner; if you do not know yours, the default gets you close.

Got a number? Let's make sure it works on the car.

Tell us the chassis, corner weights if you have them, tire, ride height and how you use the car. We confirm spring rates and valve the dampers to them before anything is built.

Spec your build with us